CAR OBDII: Lonsdor K518ISE to do Volvo S60 Smart Key Program

The following article is the guide on programming Volvo S60 smart key by Lonsdor K518ISE. As a new auto key programmer Lonsdor K518ISE leads a hot discuss. And there are many video sample about it on Youtube. Now, let us see how it program Volvo S60 Smart key and all key lost.

Lonsdor K518ISE sale link:

http://www.eobdtool.co.uk/wholesale/lonsdor-k518ise-key-programmer.html

Before all operation, please connect the car OBD to "Module identification", which can detect the module (CEM / KVM) status, distinguish if the car is full key-less or half-key-less.
Test status results: (1) Installed. (Indicating that the corresponding module status is normal)
(2) No installation or communication failure. (That the car does not have the corresponding module, or the module status is abnormal)
After the backup of the safety data is completed, install back all the modules accordingly. Please do “Module identification” again, check to ensure that the module is well installed and in normal status. And then do programming operation.
Read CEM security data:

Volvo's CEM are located under the co-pilot airbag on the left, the removal of the co-pilot glove;

Volvo's CEM is basically located behind the storage box which is in front of the co-pilot seat

CEM boxes may have the same appearance, but the back of the circuit wire location is different, can be called type A and B .

Type A: open the lid, pay attention to the black columns in the blue circle on the back of the circuit board, those are four positioning points, stably match them respectively with the white columns on RN-01 board.
Note: The circuit board is coated with insulating glue, it is required to use the washing plate water to wash it off the blue area of the insulation coating in the contact point (solder joint) , or power can not go through, if the needle of RN-01 board is broken, it will need to wire in the corresponding locations.
(First time to use the adapter, please bind it with K518ISE host, please refer to"Function")

Type B: Its circuit is different from that of type B, it requires to wire to read immodata, please refer to below wire instruction:

Note: Connect power to read the data, it is required to separate RN-01 board to the motherboard to prevent conduction; welding line should not exceed 15cm.

Read KVM security data:

Volvo's KVM modules are located in the rear of the car rear, right rear wheel position (16 S60L recommended from the right rear door to the wheel direction);

Open the module cover, you must first use the washing plate to clean the blue area of the insulation coating,

or power can not go through, please bind it with K518ISE host, please refer to"Function")

The points in the red area are the 8 pin insertion points on the FS-01 board:

Notice
Part of the Volvo KVM data read failure is because the chip model is different, then please:
① use the programmer to read out the data (.bin file);
② Please contact the after-sales (phone / QQ: 4009669130) and send EEPROM data to them, then the engineers will transfer the data into a special file;
③ Then please connect K518ISE to the computer, put the special file into the”file ---> feature_35”folder;
④ Please continue programming to select the KVM data from the process.
Read KVM data with programmer:

Attention

When K518ISE programming Volvo 6-button key, be sure to dismantle & read the CEM and KVM, as to their location and how to read them, please refer to the "Operation" or "Reference".
It is required to bind the adapter when using it for the first time, you need to bind it with K518ISE. Go to the device home page and choose "Settings -> Bind adapter", following the direction to finish binding. One K518ISE host can bind up to 5 adapters, and the bound adapter can not be bound to other K518ISE hosts. Once bound, no need to bind again.
For 5-button key, you only need to dismantle&read the CEM in co-pilot storage box to backup security data, for 6-button key, you need to dismantle&read the CEM in co-pilot storage box, as well as the KVM in the right trunk to backup security data.
For 6-button key, you need to first insert the key into the key slot and then operate according to the directions.
Check if the card is locked when it can’t be inhaled in the key slot, locked key can’t be inhaled, a new card generally will not be locked.
When install battery to Volvo models, please pay attention that the two batteries are overlapped, separated by a white paper in between, do not just replace the above one.

Disassemble is also very simple, remove the metal key, in the place where the key lies, please find a little knife with not too sharp blade, gently open it from the gap.
Reference
Chip model:Dedicated chip（brand new）
Remote type:433 frequency
Key embryo no.:No.24/38
PIN code requirement:Dismantle & read CEM to backup security data and program
Remote generation:Program smart key complete, remote will automatically generated
Under the lower-left of the steering wheel: